青岛招聘

    

1. Monitor, record and report all activities associated with surface preparation and coating.

  

2. Review and familiarize with Project Codes/Specifications/Procedures/Method Statements/Manufacturers Data sheets Project Quality Plan, (PQP), and Inspection and Test Plan, (ITP), for coating application.

  

3. Ensure the calibration/validation of all inspection equipment and tools in use , both Company and Sublet.

  

4. Check Blasters/Painters qualification against approved Project register.

  

5. Check any blasting medium is of the required type and ensure that it is certified.

  

6. Ensure atmospheric conditions are met prior to any surface preparation.

  

7. Monitor the Air Temperature, Dew Point and Relative Humidity as required by Project Specifications, PQP, and ITP prior to blasting and throughout coating application.

  

8. Verify that all surfaces are in compliance with Project Specification requirements.

  

9. Particularly ensure that “feathering” onto pre-applied coating, either during partial application or repair, has been completed to Project requirements.

  

10. Ensure caulking/masking where necessary has been completed satisfactorily.

  

11. Where hand tools are used for surface preparation, particularly in the case of repair areas, ensure that tools are of the correct type, eg, iron free on stainless steel and exotic materials.

  

12. Check cleanliness and humidity of blast/coating compressed air supply.

  

13. Check that nozzle sizes, air pressures and volumes are as per manufacturers recommendations for both blasting and coating application..

  

14. Report all surface defects to subcontractor at the prep stage, intermediate coat and final finish and rectify per Project requirements.

  

15. Ensure that all sensitive areas are protected, eg flange faces and threads, etc, and that all hollow sections are protected against detritus/debris/ blasting media ingress prior to any surface preparation..

  

16. Ensure that all coating products are of the correct manufacture, type, colour and record this and the batch numbers.

  

17. Witness coating thinning and mixing, ensure that correct mixing and thinning to Project specifications has taken place..

  

18. Check final colour coat is as required by Project specification against linelist..

  

19. Initiate Inspection requests for client’s monitoring inspections.

  

20. Inspect Wet Film Thickness, (WFT), and Dry Film Thickness, (DFT), as required by the Project Specifications, PQP and ITP.

  

21. Carry out Holiday Testing when applicable using calibrated equipment as required by the Project Specifications, PQP and ITP.

  

22. Prepare the inspection reports and records.

  

23. Witness and document test panels where required.

  

24. Complete the required testing of mock-up, (test), panels and document results.

  

25. As many of the dusts and vapours associated with blasting and coating are hazardous to your health, may be flammable and can cause reduced visibility, it is imperative and mandatory that Inspectors take precautions against inhalation and are keenly observant of unsafe acts, which should be stopped and reported to the Company HSE Department immediately.

  

26. Generate and maintain registers and progress as may be required and advised by the QC Lead Inspector Coating

  

27. In addition to the above other duties as may be assigned by the QC Lead Inspector Coating.

    

Essential:

                                         In depth knowledge of   coating types, practices and processes.    Knowledge of NACE   requirements mandatory      Basic computing skills   and working knowledge of Microsoft S Office suite.                          Hands-on skills in coating application process advantageous but not   essential.   Effective communication and reporting   skills, preferably competent in both Chinese and English language, reading   and writing.      Minimum 1 year of   experience in the coating inspection field within the Oil & Gas industry.      Degree in science related subject preferable but not essential.   Junior Colleague or   above mandatory   Certificate to  NACE Level I or above is required.     

青岛武船麦克德莫特海洋工程有限公司(简称 QMW) 是由中船重工集团 (CSIC) 的全资子公司武昌船舶重工有限责任公司和McDermott International Inc. (MII) 的全资子公司J. Ray McDermott Qingdao Pte. Ltd (McDermott) 于2008年共同出资组建的合资公司，双方各拥有股权50%。 2009年开始投入建造，45公顷的建造厂区位于青岛黄岛区胶州湾海海底隧道口处， 并且毗连CSIC的北海造船厂，是海西湾船舶建造、修理基地的一部分。

合资公司将融合双方优势，麦克德莫特具有专利建造系统，程序，管理模式以及丰富的国际客户服务经验；武船拥有有效的成本控制方式，丰富的浮体建造经验。合资企业的建造的产品包括：陆上或离岸的油气处理模块，综合一体化的平台， SPAR浮体， 大型的海上浮式油气处理和储存设施（FPSO）以及为国际市场包括亚洲，墨西哥湾，地中海，中东，南海，西非的客户提供FPSO的整体服务。合资厂也将努力进入中国的陆上和离岸市场。

QMW为员工建立多元化的职业发展阶梯及培训模式，并提供宽阔的个人发展平台及有竞争力的薪酬福利体系，让员工充分展现自己的才华，不断地提升自身价值并享受与公司共同发展的成果。QMW欢迎社会各位优秀人才的加入！

公司网站：*******************************
地址：青岛经济技术开发区漓江东路367号