Sr Mfg Product Engineer产品工程师 -全球最大的闪速数据存储卡产品供应商，丰厚薪资，广阔空间(职位编号：1)
上海帝博企业管理咨询有限公司
- 公司规模：少于50人
- 公司性质：外资(欧美)
- 公司行业：专业服务(咨询、人力资源、财会)
职位信息
- 发布日期：2013-06-20
- 工作地点：上海
- 招聘人数：1
- 工作经验：五年以上
- 学历要求：大专
- 语言要求：英语熟练
- 职位类别：半导体技术 项目经理/主管
职位描述
Position Summary
? Support Product Transitions from Design to Manufacturing
-Bridge development from Design to high volume manufacturing
-Work with SDUS Product and Test engineering to Develop cost effective test solutions
? Customer Satisfaction
-Meet internal and external customer requirements
-Yield Enhancement
-Monitor and drive for increased product test yields
? Quality Improvement
-Enhanced test coverage to meet customer requirements
? Cost Reduction
-Drive to implement test time reductions at all test process steps
-Cycle time reduction
Responsibility
New Product Introduction
? Implement Test Plan for new products.
? Checkout new test program releases in Production environment and officially release program to Production floor.
? Release temporarily program to Production floor to test out AI build.
? Set up, buy off new test station and implement supplemental test stations.
? Implement and develops Test Process Flow and test system controls cater for volume production.
? Merge engineering database with Production database to test AIs.
? Provide technical training of key test flow and process to CM Test Manufacturing Engineering.
Product Support
? Responsible for Failure Analysis for product yield improvement and meeting yield and quality target.
? Support daily activities on hold lot dispositions from low yield and QA reject and give timely disposition to CM.
? Provide on going technical training of products to key Production personnel including CM FA, Quality, Assembly and Packaging team.
? Drive Test time reduction and yield improvements on active products.
? Validate and approve ECOs regarding BOM updates of existing products.
? Generate Production Database and Release via TCN process after ECO released. Approve TCN.
Test Program and Test Station Management
? Volume checkout new test program releases in Production environment and officially release program to Production floor via TCN Process.
-Manage and generate TCN
? Support Production Security key renewing and installation.
? Oversee installation and set up of new test equipment. Buyoff new test equipment.
? Reliability test full QAWR (responsible for 1st level eFA to isolate invalid vs. valid reject).
Manufacturing/ Quality Support
? OBA and OQRM reject FA in CM
? New OQRM host implementation in CM
? Support RMA and MRB disposition
? Participate in Quality and customer audits
? Customer complaint investigation
? Work closely with QA and CME to improve test processes
? Generate test reclaim process and disposition
Qualification:
? Must be fluent in English oral and written.
? Masters degree is a plus.
? System level/ PCBA test engineering experience and C/C++ knowledge is a plus.
? Support Product Transitions from Design to Manufacturing
-Bridge development from Design to high volume manufacturing
-Work with SDUS Product and Test engineering to Develop cost effective test solutions
? Customer Satisfaction
-Meet internal and external customer requirements
-Yield Enhancement
-Monitor and drive for increased product test yields
? Quality Improvement
-Enhanced test coverage to meet customer requirements
? Cost Reduction
-Drive to implement test time reductions at all test process steps
-Cycle time reduction
Responsibility
New Product Introduction
? Implement Test Plan for new products.
? Checkout new test program releases in Production environment and officially release program to Production floor.
? Release temporarily program to Production floor to test out AI build.
? Set up, buy off new test station and implement supplemental test stations.
? Implement and develops Test Process Flow and test system controls cater for volume production.
? Merge engineering database with Production database to test AIs.
? Provide technical training of key test flow and process to CM Test Manufacturing Engineering.
Product Support
? Responsible for Failure Analysis for product yield improvement and meeting yield and quality target.
? Support daily activities on hold lot dispositions from low yield and QA reject and give timely disposition to CM.
? Provide on going technical training of products to key Production personnel including CM FA, Quality, Assembly and Packaging team.
? Drive Test time reduction and yield improvements on active products.
? Validate and approve ECOs regarding BOM updates of existing products.
? Generate Production Database and Release via TCN process after ECO released. Approve TCN.
Test Program and Test Station Management
? Volume checkout new test program releases in Production environment and officially release program to Production floor via TCN Process.
-Manage and generate TCN
? Support Production Security key renewing and installation.
? Oversee installation and set up of new test equipment. Buyoff new test equipment.
? Reliability test full QAWR (responsible for 1st level eFA to isolate invalid vs. valid reject).
Manufacturing/ Quality Support
? OBA and OQRM reject FA in CM
? New OQRM host implementation in CM
? Support RMA and MRB disposition
? Participate in Quality and customer audits
? Customer complaint investigation
? Work closely with QA and CME to improve test processes
? Generate test reclaim process and disposition
Qualification:
? Must be fluent in English oral and written.
? Masters degree is a plus.
? System level/ PCBA test engineering experience and C/C++ knowledge is a plus.
公司介绍
DB Talent is a European based recruitment company. Our Shanghai office opened in the 2001, and we have continually provided excellent professional service to our clients and candidates.
联系方式
- 联系人：resume
- 电话：13701722965